Soft pack special engraving machine: Ming Wang from Shenzhen home Limited soft pack produced according to the special requirements of integrated software packages for 12 years of production experience and digital engineers dedicated to improving the well-made soft pack special open board machinery. Using a unique pressure roller fixation, imported high-quality machine spindle, rails, provide a strong guarantee for the high-efficiency, high-precision production of soft package. First, the engraving machine technical parameters and processing parameters table size (mm): 1300 * 2500 speed :( r / min) 24 000 maximum engraving size (MM): 1300 * 2500 Z-axis travel (mm): 200 Dimensions (mm) : 1600 × 3100 × 1800mm resolution (MM / pulse 0.001) Shank Diameter: 12.7 \ 8 \ 6 \ 3.175 Spindle motor power: 4500W Rated voltage: 380V Second, the engraving machine installation Precautions 1. Do not install this device during lightning or thunder, do not install power outlets in damp places, do not touch uninsulated power lines. 2. The machine operator must go through rigorous training, during operation must pay attention to personal safety and the safety of the machine, and strictly follow the rules to operate a computer engraving machine. 3. Power supply voltage requirements 220V or 380V, if the power supply voltage instability or around high-power electrical equipment, be sure to select the power supply under the guidance of professional and technical personnel. 4. Engraving machine, control cabinet must be effectively grounded, connect the data cable is not charged. 5. Operating personnel must not wear gloves work best to wear protective goggles. 6. Mechanical body for the steel gantry part aerospace aluminum casting, relatively soft when mounting screws (especially the installation carving motors) Do not be too hard to slip wire. 7. The tool must be installed and clamped, keeping knives sharp, blunt instrument engraving quality will decline overload the motor. 8. Do not put fingers extending the scope of work tools, do not remove the engraving head to other uses. Non-processed materials including stone white cotton. 9. Do not exceed the machining range, to cut off the power when the long inoperative, the machine moves, there must be carried out under the guidance of professional presence. 10. The machine abnormal situation, please see the operating manual troubleshooting chapter or contact your dealer to resolve; to avoid man-made damage. 11. Where the control card must be installed and connected to the computer plugged in tight and tighten the screws. Third, the machine installation WARNING: All operations shall be operated off! ! ! ! 1. The machine body and connected to the control box. 2. The control data line terminal is connected to the machine body on the control box. 3. Plug the power cord is plugged into the machine body on the Chinese standard 220V power supply. The control box connected to the computer, the data cord plugged into the control box of the data signal input port and the other end plugged into the computer. 5. Connect the power cord plugged into the control box power supply, and the other end is connected to a standard 380V power source. 6. chisel through the collet chuck mounted on the bottom of the spindle. When first loaded into the tool in the spindle taper collet chuck in the right size, then the tool into the hole chuck, with random small wrench spindle neck flat groove, so it can not rotate, then big wrench counterclockwise rotation locking screw spindle mother, the prison tool. Fourth, the engraving machine operating procedures 1. according to customer requirements and design requirements for typesetting, in the correct path After calculation, the path different tools to be saved. Saved as a different file. 2. After checking the correct path in the engraving machine control system in the path of the file to open (to preview). 3. Fixed good material, good working definition of origin. Open the spindle motor improvement in the number of correct tune. 4. Turn on the power for machine operation. 4.1 Power 4.1.1. Turn the power switch, power indicator light, the machine reset self-test run first, X, Y, Z, axis reset to zero, then their run to the initial standby position (initial machine origin). 4.1.2 Using the hand-held controller, respectively, X, Y, Z axis to adjust the alignment starting point engraving work (processing origin). Spindle speed, feed rate are appropriately selected, the engraving machine is working a wait state. 4.2 engraving 4.2.1 file to be edited carvings. 4.2.2 Open transfer files to transfer files to the engraving machine, carving work can be done automatically documents. 4.3 end when the end of file carving, carving automatically carrying knives, and run to the top of the work starting point. V. Troubleshooting of 1, fault alarm, overtravel alarm, indicating the machine during operation has reached its limit position, check the following steps: 1.1, the design process is beyond the scope of image size. 1.2, check the motor shaft and screw machine cable is loose, if it is, please tighten the screw. 1.3, the machine and the computer is properly grounded. 1.4, the current coordinate value exceeds the software limit value range. 2, when overtravel alarm and lift overtravel, all axes are automatically set in motion to move the state, as long as holding the arrow keys to manually restore the connection state of motion when the machine is left limit position (ie, points out overtravel switch) at any time Note that the direction of movement of the mobile table, must stay away from extreme positions. software limit alarm settings need to coordinate XYZ can be cleared. 3, non-alarm fault 3.1, repeat precision is not enough, according to Article 1, paragraph checks. 3.2, the computer is running, the machine does not move, check the computer control card and the computer box connector is loose, Wakamatsu is seated, and tighten the screws. 3.3, the machine can not find a signal back to mechanical origin, in accordance with article 2 Check mechanical origin proximity switch failure. Fourth, the output fault 1. Do not output, check the computer and the control box is connected. 2. Open engraving Manager settings where space is full, within delete unused files manager. 3. The signal line wiring is loose, carefully check the line is connected. Fifth, the engraving machine malfunction self-examination 1, whether the various parts of screws loose. 2. Check whether the correct path to deal with their own. 3. whether the files caused by too much computer processing error. The changes in the spindle speed to suit different materials (typically 8000-24000)! Note: continuously variable spindle idle speed used for 6000-24000 range, depending on the hardness of the material, processing and feed quality requirements volume size and other factors appropriate choice of speed, usually hard material, a small amount of feed, requires selection of high-speed engraving fine when, typically, do not crank up the speed, so as not to overload the motor. 5, loosen the knife chuck, the knife turn directions clamped knife being put to avoid carving objects is not smooth. 6. Check whether the tool detrimental to put a new knife, re-engraving. Note: Do not drill into the housing in the engraving machine marking, otherwise it will damage the insulation layer, when necessary, to paste mark six, routine maintenance and servicing system engraving machine engraving machine CNC system belongs to a class on the grid environment constant. requirements, the system where the power line should be no welding, machine tools, power tools, radios, etc., strong grid disturbance easily lead to frequent starting work computer and engraving machine system abnormalities. Engraving machine maintenance is to ensure the life and improve the efficiency of an important means of equipment! 1. In actual use, in accordance with normal operating specifications. 2. Routine maintenance work is completed requires daily work surfaces and equipment clean refueling to avoid unnecessary losses. 3. Regular maintenance requirements once a month to maintain the purpose is to check all parts of the machine screw is loose, ensure that the machine lubrication conditions and good environmental conditions. 4. In order to avoid a power outlet is loose or making poor contact caused by abnormal processing of product obsolescence, select a good outlet should have a reliable ground protection.